3D Printing

If you like to tinker and want to explore the exciting world of 3D printing consider 3D Printer Kits from “You-Do-It” Electronics Center. Learn the ins-and-outs of 3D printing by building your own 3D printer from a 3D printer kit. Once assembled use your 3D printer to explore to possibilities of building 3D models before deciding if you want to invest in a fully-assembled machine. Discover why 3D printer kits are the best way to jump into 3D printing – providing you are willing to tinker with your machine. Questions – ask the expert staff at “You-Do-It” Electronics Center.
Items 1 to 36 of 93 total

Grid List

3M Polyimide Film Tape Heat Resistant 1/2" x 36yd, 1205

.5 inch width X 36 yard roll Designed for high heat applications Tough and thin Solvent-resistant 

VELLEMAN Flat 15 Conductor Ribbon Cable for K8200 3D Printer 3m, FC16C-3/SP

15 Conductor Multi-Colored Cable Used to help modify or repair K8200 3D printer

VELLEMAN Replacement Glass Bed Panel for K8200 3D Printer, GP8200

material: clear tempered glass thickness: 0.12" (3mm) size: 8.46 x 8.46" (215x215mm) ensures a perfectly flat and level bed smoother finish of bottom layer tempered glass: less likely to shatter than ordinary window glass or mirrors

VELLEMAN NTC Thermistor (Version 2) for K8200 3D Printer, NTC104LAF/SP

The spare part, NTC104LAF/SP is a 100k NTC Thermistor for the second generation hot end on the K8200 3D Printer Fits through a hole in the heater block for better temperature control of the extruder’s hot end The thermistor provides feedback to the controller for temperature control

VELLEMAN Extruder Upgrade Kit for K8200 3D Printer, K8203

Print with 1.75mm PLA or ABS filament on your Velleman K8200: 3D Printer Higher resolution 3D prints EXTRUSION UPGRADE KIT INCLUDES: 0.35mm extruder nozzle for 1.75mm filament Extruder heater and sensor Direct drive unit with stainless steel pulley High power plug-in stepper driver All necessary installation hardware

VELLEMAN Z-axis Upgrade Rod and Coupler for K8200 3D Printer, K8204

Improves Z-axis accuracy Eliminates printing wobble Strongly advised for direct drive 0.35mm printing Upgrade Kit Includes: Precision threaded rod lead screw Follower Nut Flexible coupler

VELLEMAN Themistor NTC 100K SMD for K8200 3D Printer, NTC100K-1206/SP

An inexpensive temperature sensitive resistor, composed of semiconductor material NTC 100k SMD 10% 2-pin 1206 for K8200

VELLEMAN Linear Bearing 10mm for K8200 3D Printer, LM10UU/SP

These bearings provide free motion for the K8200 3D Printer linearly, or in one direction Linear bearings do not require any lubrication or maintenance, but keep a few stashed away just in case

VELLEMAN Linear Bearing for K8200 3D Printer, LM8UU/SP

This standard .8mm bearing will replace any bearing included in the K8200 3D printer Bearings play an important role in 3D printing, make sure your K8200 is running smoothly and effectively by replacing any faulty bearings.

VELLEMAN Stepper Motor for K8200 3D Printer, MOTS4/SP

2.5Ah 1.8 Steps Inexpensive, replacement stepper motor for the K8200 3D Printer

VELLEMAN Plastic Parts Set for K8200 3D Printer, MP8200SET/SP

The MP8200SET/SP includes all plastic parts need for assembly of the K8200 Black Plastic

VELLEMAN PCB for Bed Plate for K8200 3D Printer, P8200BED/SP

The Velleman P8200BED/SP is the heating element for the K8200’s heated bed This product does not contain the glass plate on which you actually print

VELLEMAN Extruder for K8200 3D Printer, 7350-31/SP

The Velleman 7350-31/SP includes: 5mm nozzle and barrel heater element heater block NTC thermistor filament guide tension relief bracket and isolator necessary hardware for assembly

POLOLU A4988 Stepper Motor Driver, A4988/SP

Replacement stepper motor driver card for Velleman K8200 3D Printer  Controls the MOTS4/SP Stepper Motors of the K8200 3D Printer Can be used with a wide variety of stepper motors Simple step and direction control interface Five different step resolutions: full-step, half-step, quarter-step, eighth-step, and sixteenth-step Adjustable current control lets you set the maximum current output with a potentiometer, which lets you use voltages above your stepper motor’s rated voltage to achieve higher step rates Intelligent chopping control that automatically selects the correct current decay mode (fast decay or slow decay) Over-temperature thermal shutdown, under-voltage lockout, and crossover-current protection Short-to-ground and shorted-load protection
New VELLEMAN 3D Printer Head LED Light Ring

VELLEMAN 3D Printer Head LED Light Ring, VM8202

Power supply: 15 VDC (from driver board) Power consumption: approx. 65 mA Ring diameter: 80 mm / 3.15"

VELLEMAN Stand Alone Controller for K8200 3D Printer, VM8201

Encoder based control. Enclosure .STL file available from K8200 website SD card slot. Reset button. Dimensions: 80 x 50 x 45 mm / 3.15 x 1.96 x 1.77"

VELLEMAN CPU Board for K8200 3D Printer, VK8200/SP

If your not happy with the speed of the 3D printer, it may be time to replace the CPU.  This controller board comes fully soldered and requires no assembly.  Contains header connections for extruder heating, cooling and motors; filters for noiseless operation.

MG Chemicals Polymide Tape, POL200-15

20cm x 15m (8in x 49ft) 2 mils thick Silicone adhesive Very high heat resistant Superior tensile strength Eases release of heated objects Protects printer bed RoHS and REACH compliant

VELLEMAN Spare Nozzle Assembly for K8200 3D Printer, NOZ8200/SP

Replaces clogged or Jammed Printer Nozzle Remove, replace, and reprint with the Spare Nozzle Assembly

VELLEMAN Flexible Z-axis Coupling for K8200 and K8400 3D Printers, ZC3DJT16

diameter: 16mm / 0.63" length: 23mm / 0.91" inside diameter: 5mm (0.20") / 8mm (0.31") material: 7075 aluminium max torque: 1Nm axial flex: +/- 0.4mm (0.0157") lateral flex: 0.1mm (0.004")

VELLEMAN Power Adapter 15VDC 100W for 3D Printer, PSK8200/SP

Replace your malfunctioning power supply with the Velleman PSK8200/SP spare power adapter. Power Supply to bare leads: 15vdc 100w

VELLEMAN DRV8825 Stepper Driver Board for K8400, VM8400DB

simple step and direction control interface six different step resolutions: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step current adjust trimmer can interface directly with 3.3 V and 5 V systems over-temperature thermal shutdown, over-current shutdown and under-voltage lockout short-to-ground and shorted-load protection minimum operating voltage: 8.2 V maximum operating voltage: 45 V continuous current per phase: 1.5 A maximum current per phase: 2.2 A (with cooling) minimum logic voltage: 2.5 V maximum logic voltage: 5.25 V dimensions: 20 x 15 mm (0.8" x 0.6 ")

MG CHEMICALS Acetone 945ml, 434-1L

Enhances Adhesion to the Print Bed for 3D Printing Smooth Finishing of 3D Printed Pieces Highly Miscible with Other Common Organic Solvents Fast Evaporation Rate VOC Exempt

MG CHEMICALS D-Limonene Pure Grade 945ml, 433-1L


VELLEMAN Vertex Nano 3D Printer Assembled, VM8600

printing: print technology: Fused Filament Fabrication (FFF) layer resolution: standard: 0.1 mm (maximum: 0.2 mm - minimum: 0.05 mm) build plate: 80 x 80 mm build volume: 80 x 80 x 75 mm / 3,15 x 3,15 x 2,95" build plate surface: Metal plate with BuildTak™ (consumable, also sold separately) print speed: 40mm/s travel speed: 70mm/s filament diameter: 1.75 mm prints: PLA, ABS (testing with other materials in progress) maximum nozzle operating temperature (extruder location: back): 245 °C maximum nozzle operating temperature (extruder location: front): 260 °C software: firmware: Modified Open Source Marlin 3D Printer. Firmware - user upgradable software: Repetier - CuraEngine - Slic3r (RepRap compatible) hardware: dimensions: 230 x 150 x 160 mm / 9 x 5,9 x 6,3" frame: sturdy, metal frame weight: 2.3 kg / 5 lb average noise level during operation: 45dB(A) ambient operation temperature: max 25 °C storage temperature: - 10 °C to + 40 °C electrical: communication: an SD card for direct printing and a USB connection for updates controller board: AVR ATmega2560 based display: 4 x 20 char. blue LCD with white backlight AC input: 100-240 V , 50/60Hz LED illuminated logo

VELLEMAN Vertex Delta 3D Printer, K8800

Printing: print technology: Fused Filament Fabrication (FFF - FDM) layer resolution: standard 0.1 mm (maximum: 0.2 mm - minimum: 0.05 mm) large build volume: 200 mm build platform diameter (0/- 5 mm), 225 mm build height (0/+75 mm) (depends on object diameter) print speed: 20-50 mm/s (can go up to 75 mm/s) travel speed: 180-200 mm/s build plate surface: removable layer of BuildTak™ (K8800-BT) filament diameter: 1.75 mm (accepts all filament spools with a mounting hole = 53 mm) - open filament policy prints: PLA, ABS, TPU, PET and others nozzle: E3D compatible nozzle diameter: 0.35 mm (one nozzle supplied) maximum nozzle operating temperature: 295°C bed compensation: automatic bed compensation performed by the nozzle (no manual calibration needed) calibration: automatic first-time set-up calibration couplers: backlash free magnetic effector-couplers advanced safety features: auto shutdown when print head detaches or temperature is incorrect (most unlikely) filament run out detector: automatic pause and reload when printer runs out of filament change filament function while printing: this means that you can print objects with multiple filaments/colours effective pause function: pause your print job without nozzle leakage end stops: infrared based end stops software: firmware: modified Open Source Marlin 3D Printer, firmware is user upgradable software: custom Repetier version (Windows) - Cura profiles (Mac) hardware: dimensions: W 35 x D 35 x H 77 cm (without filament spool) frame: rigid aluminium extrusion risers and 4 mm aluminium top and bottom plates for a sturdy frame and precision ground 100 mm vertical rods and brass bushings fully Open-Source (hard- and software) weight: 10 kg ambient operating temperature: max. 30°C storage temperature: -10°C to +50°C hybrid kit: quick and straightforward build, no soldering required Electrical: communication: SD card or USB 2.0 (automatic SD card recognition) controller board: AVR ATmega2560 based AC input: 100 - 240 VAC 50-60 Hz 90 W max. display: 128 x 64 px graphic display with blue backlight