Development Board

33 Item(s)

Grid List

VELLEMAN 2-Channel Power Module for Breadboards 3., VMA424

$4.75
input voltage: 7-12 VDC or USB 5 V power supply (use regulated supply) output voltage: 5 VDC fixed + 3.3 V / 5 V, switchable maximum output current: maximum 500 mA, onboard 500 mA resettable fuse two power rails: 1 rail fixed 5 V the other selectable 3.3 V or 5 V DC input: 5.5 x 2.1 mm plug

VELLEMAN Audio Shield for Arduino Kit, KA02

$19.90
60 second recording time start playback, record,… via on-board buttons or via Arduino® UNO playback via a speaker or a line output downloadable sample sketch and library stackable design: the shield can be stacked with other shields large user community requires 1 Arduino UNO™ (not included) audio sample frequency: 8 kHz uses pin 10 on an Arduino UNO™ board as a Chip Select uses the ICSP pins on an Arduino as a serial connection to the shield to free up I/O pins memory write up to 100.000 X dimensions: 71 x 53mm / 2.79 x 2.08"'

VELLEMAN Arduino STEM Shield with Sensors, KAEDU

$24.35
temperature sensor light sensor 7-segment display 2 stoplight simulations (6 LEDs) 4 tactile buttons 1 slide switch 1 potentiometer 1 sounder 1 servo connection 1 infrared LED all modules are 'disconnectable' so the Arduino pins can by used freely a 'line follower' sensor can by made with the IR LED and light sensor the 7- segment and line follower module can be separated from the main PCB fully Arduino compatible

VELLEMAN Microbit Starter Kit, VMM001

$39.90
contains: USB cable: 1 x (PAC610B007N) housing for microbit: 1 x battery holder: 1 x microbit: 1 x battery: 4 x AAA (LR03C) microbit hardware: lights: 5 x 5 LED matrix buttons: 2 push buttons compass: detect magnetic fields accelerometer: detect changes in the microbit speed GPIO: 17 general purpose input / output pins Bluetooth: Bluetooth Low Energy (BLE) processor: 16 MHz ARM Cortex - M0 microcontroller 32-bit processor connectivity: Bluetooth Low Energy (BLE) USB: USB 2.0 port and micro-USB connector GPIO: up to 17 general purpose input / output pins RAM: 16 KB static RAM power supply: battery holder: 2 x AAA micro-USB connector dimensions: microbit: 51 x 42 x 10 mm battery holder: 62 x 25 x 15 mm

VELLEMAN Microbit Advanced Kit, VMM002

$59.90
contains: USB cable: 1 x (PAC610B007N) microbit project holder, breakout board & components: 1 x microbit: 1 x battery: 4 x AAA (LR03C) microbit hardware: lights: 5 x 5 LED matrix buttons: 2 push buttons compass: detect magnetic fields accelerometer: detect changes in the microbit speed GPIO: 17 general purpose input / output pins Bluetooth: Bluetooth Low Energy (BLE) processor: 16 MHz ARM Cortex - M0 microcontroller32-bit processor connectivity: Bluetooth Low Energy (BLE) USB: USB 2.0 port and microUSB connector GPIO: up to 17 general purpose input / output pins RAM: 16 KB static RAM power supply: microbit project holder: 2 x AAA micro usb connector dimensions: microbit: 51 x 42 x 10 mm microbit project holder, breakout board: 158 x 105 x 24 mm

OSEPP STEM Kit 1 Starter Kit, STEM-01

$149.95
100% Arduino Compatible Learn the most common Arduino functions with one board! Minimal cable ‘jumping’ required.  More time spent on actual LEARNING! 8 Output Devices 8 Input Devices Includes graphical TUTORIAL BOOKLET (for use with OseppBlock IDE) For ages 10+ No assembly required Includes protective case Includes OSEPP UNO R4 Plus Board (microcontroller)

TEENSY LC Development Board, TEENSYLC

$12.95
ARM® Cortex-M0+ Processor at 48 MHz 62k flash memory, 1/8 (emulated) EEPROM, 8k RAM 12 bit analog input & output 27 I/O pins 13 Analog inputs 1 Analog output 10 PWM outputs 3 Serial 2 SPI 2 I2C 1 I2S (for high quality audio interface) Dimensions: 1.38” x 0.7” (35mm x 17.78mm)

RASPBERRY PI Sense Hat Astro Pi, 83-16980

$35.00
Gyroscope – angular rate sensor: +/-245/500/2000dps Accelerometer - Linear acceleration sensor: +/-2/4/8/16 g Magnetometer - Magnetic Sensor: +/- 4/8/12/16 Gauss Barometer: 260 – 1260 hPa absolute range (accuracy depends on the temperature and pressure, +/- 0.1 hPa under normal conditions) Temperature sensor (Temperature accurate to +/- 2 degC in the 0-65 degC range) Relative Humidity sensor (accurate to +/- 4.5% in the 20-80%rH range, accurate to +/- 0.5 degC in 15-40 degC range) 8x8 RGB LED matrix display Small 5 button joystick Compatible with Raspberry Pi B+, A+, and Pi 2

VELLEMAN WiFi ESP8266 Arduino Shield, VMA205

$24.65
802.11 b / g n wireless standards STA / AP modes support TCP / IP protocol stack, One socket supports standard TCP / UDP server and client supports serial port baud rate configuration: 1200 / 2400 / 4800 / 9600 / 19200 / 38400 / 57600 / 74800 / 115200 bps supports serial data bits: 5 / 6 / 7 / 8 bits supports serial stop bits: 1/2 bit pin-compatible with Arduino Uno, Mega Arduino pinout: 2/3/4/5/6/7/8/9/10/11/12/13 ESP8266 GPIO pinout: 0/2/4/5/9/10/12/13/14/15/16 / ADC / EN / * UART TX / UART RX KEY button: modes configuration dual-ports DIP switches: switching Arduino and ESP8266 WiFi operation current: continuous transmission operation: ˜70 mA (200 mA max), idle mode: < 200 uA serial WiFi transmission rate: 110-460800 bps operating humidity: 10%-90% non-condensing operating temperature: -10 to 70 °C weight: ± 20 g (0.7 oz)

VELLEMAN Nodemcu V2 lua based ESP8266 WiFi Development Board, VMA107

$16.25
operating voltage: 5 VDC (USB) dimensions: 5.8 x 3.2 x 1.2 cm weight: 12 g low-cost WiFi solution programmable with the Lua scripting language on-board USB-serial adaptor PCB antenna (no external antenna required) 10 GPIO pins, each GPIO can be PWM, I2C, 1-wire bread-board compatible powered via microB USB

VELLEMAN Atmega32u4 Wearable Lilypad Development Board, VMA105

$18.05
microcontroller: ATmega32U4 operating voltage: 2.7 - 5.5 VDC input voltage: 2.7 - 5.5 VDC digital I/O pins: 9 PWM channels: 4 analogue input channels: 4 DC current per I/O pin: 40 mA flash memory: 32 KB (of which 4 KB used by bootloader) SRAM: 2.5 KB EEPROM: 1 KB clock speed: 8 MHz diameter: 50 mm 100% compatible with Arduino® Liliypad

ARDUINO Pro Mini 328 - 5V/16MHz, DEV-11113

$9.95
ATmega328 running at 16MHz with external resonator (0.5% tolerance) 0.8mm Thin PCB USB connection off board Supports auto-reset 5V regulator Max 150mA output Over current protected Weighs less than 2 grams! DC input 5V up to 12V On board Power and Status LEDs Analog Pins: 8 Digital I/Os: 14

ARDUINO Pro Mini 328 - 3.3V/8MHz, DEV-11114

$9.95
ATmega328 running at 8MHz with external resonator (0.5% tolerance) Low-voltage board needs no interfacing circuitry to popular 3.3V devices and modules (GPS, accelerometers, sensors, etc) 0.8mm Thin PCB USB connection off board Weighs less than 2 grams! Supports auto-reset 3.3V regulator Max 150mA output Over current protected DC input 3.3V up to 12V On board Power and Status LEDs Analog Pins: 8 Digital I/Os: 14

SPARKFUN Mini Inventor's Kit for Redboard, DEV-13160

$49.95
Circuit Examples: Circuit 1: Blinking an LED Circuit 2: Reading a Potentiometer Circuit 3: Driving and RGB LED Circuit 4: Driving Multiple LEDs Circuit 5: Push Buttons Circuit 6: Reading a Photo Resistor Circuit 7: Reading a Temperature Sensor Circuit 8: Driving a Servo Motor

TEENSY Audio Adapter Board, TEENSY-AUDIO-SD

$14.95
16 bit, 441 kHz Sample Rate Audio Plays Uncompressed WAV and Raw Audio Files 4 Channel Software Mixer 3.5mm Audio Jack micro-SD Card Slot

TEENSY 3.2 Development Board, TEENSY3.2

$24.95
32 bit ARM Cortex-M4 72 MHz CPU (M4 = DSP extensions) 256K Flash Memory, 64K RAM, 2K EEPROM 21 High Resolution Analog Inputs (13 bits usable, 16 bit hardware) 34 Digital I/O Pins (5V tolerance on Digital Inputs) 12 PWM outputs 7 Timers for intervals/delays, separate from PWM USB with dedicated DMA memory transfers 3 UARTs (serial ports) SPI, I2C, I2S,CAN Bus, IR modulator I2S (for high quality audio interface) Real Time Clock (with user-added 32.768 crystal and battery) 16 DMA channels (separate from USB) Touch Sensor Inputs

VELLEMAN Robot Car Chassis Kit - 2 Wheel Drive, VMA500

$23.60
Pre-drilled mounting plates One DC motor and gearbox per wheel 2 Wheels 1 Supporting Wheel 2 DC Motors wtih gearboxes 1 Vehicle chassis 1 Top cover with mounting hardware

VELLEMAN Protoshield Prototyping Board with Mini Breadboard for Arduino Uno, VMA201

$5.45
1.0 Arduino Pinout reset button free to use button + LED circuit ICSP connector location 14 pin SMD footprint 20 pin through-hole footprint 170 holes self-adhesive breadboard included compatible with: Leonardo, Uno, Mega, Classic

VELLEMAN Atmega328 Uno Development Board, VMA100

$14.75
100% compatible with Arduino® Uses lastest Atmel ATmega328 microprocessor Specs: microcontroller: ATmega328 operating voltage: 5 VDC input voltage (recommended): 7-12 VDC input voltage (limits): 6-20 VDC digital I/O pins: 14 (of which 6 provide PWM output) analogue input pins: 6 DC current per I/O pin: 40 mA DC current for 3.3 V pin: 50 mA flash memory: 32 kB (ATmega328) of which 0.5 kB used by bootloader SRAM: 2 kB (ATmega328) EEPROM: 1 kB (ATmega328) clock speed: 16 MHz length: 2.7" (68.6 mm) width: 2.1" (53.4 mm) weight: 0.88 oz. (25 g)

VELLEMAN Atmega2560 Mega Development Board, VMA101

$24.90
100% compatible with Arduino® Uses lastest Atmel ATmega2560 microprocessor Specs: microcontroller: ATmega2560 operating voltage: 5 VDC input voltage (recommended): 7-12 VDC input voltage (limits): 6-20 VDC digital I/O pins: 54 (of which 15 provide PWM output) analogue input pins: 16 DC current per I/O pin: 40 mA DC current for 3.3 V pin: 50 mA flash memory: 256 kB of which 8 kB used by bootloader SRAM: 8 kB EEPROM: 4 kB clock speed: 16 MHz length: 4.41" (112 mm) width: 2.17" (55 mm) weight: 2.19 oz. (62 g)

VELLEMAN Atmega328 Nano Development Board, VMA102

$17.55
microcontroller: Atmel ATmega168 or ATmega328 operating voltage: 5 VDC input voltage (recommended): 7-12 VDC input voltage (limits): 6-20 VDC digital I/O pins: 14 (of which 6 provide PWM output) analogue input pins: 8 DC current per I/O pin: 40 mA flash memory: 16 kB (ATmega168) or 32 kB (ATmega328) SRAM: 1 kB (ATmega168) or 2 kB (ATmega328) EEPROM: 512 bytes (ATmega168) or 1 kB (ATmega328) clock speed: 16 MHz length: 45 mm width: 18 mm weight: 5 g 100% compatible with Arduino® NANO 3.0

VELLEMAN Atmega32U4 Leonardo Development Board, VMA103

$16.35
microcontroller: ATmega32u4 operating voltage: 5 VDC input voltage (recommended): 7-12 VDC input voltage (limits): 6-20 VDC digital I/O pins: 20 analogue input pins: 12 PWM channels: 7 DC current per I/O pin: 40 mA DC current for 3.3 V pin: 50 mA flash memory: 32 kB (ATmega32u4) of which 4 kB used by bootloader SRAM: 2.5 kB (ATmega32u4) EEPROM: 1 kB (ATmega32u4) clock speed: 16 MHz length: 68.6 mm width: 53.3 mm weight: 20 g 100% compatible with Arduino® LEONARDO

VELLEMAN Arduino Compatible DIY Kit with UNO R3, VMA501

$39.90
This basic kit includes: 1 x ATmega328 UNO DEVELOPMENT BOARD (VMA100) 15 x LED (different colors) 8 x 220 Ohm resistor (RA220E0) 5 x 1K resistor (RA1K0) 5 x 10K resistor (RA10K0) 1 x 830 hole breadboard 1 x RGB LED module (VMA318) 4 x 4-pin Key switch 1 x Active buzzer (VMA319) 1 x Passive buzzer 1 x 1838 IR Infrared 37.9Khz Receiver (VMA317) 1 x Infrared remote control 1 x infrared sensor diode 1 x LM35 temperature sensor (LM35DZ) 2 x Ball tilt switch (similar to MERS4 & MERS5) 3 x Photosenitive resistor LDR (similar to LDR04) 1 x 74HC595 Shift register (HC595) 1 x Battery holder for 6 AA battery's (similar to BH363B) 1 x 8*8 LED Matrix display 1 x single digit 7 segment LED display 1 x 4 digit 7 segment LED display 30 x Breadboard jumper wire 1 x USB cable

VELLEMAN Arduino Compatible DIY Kit with MEGA 2560, VMA502

$44.90
This kit includes: 1 x ATmega2560 MEGA DEVELOPMENT BOARD (VMA101) 15 x LED (different colors) 8 x 220 Ohm resistor (RA220E0) 5 x 1K resistor (RA1K0) 5 x 10K resistor (RA10K0) 1 x 830 hole breadboard 4 x 4-pin Key switch 1 x Active buzzer (VMA319) 1 x Passive buzzer 1 x infrared sensor diode 1 x LM35 temperature sensor (LM35DZ) 2 x Ball tilt switch (similar to MERS4 & MERS5) 3 x Photosenitive resistor LDR (similar to LDR04) 1 x single digit 7 segment LED display 30 x Breadboard jumper wire 1 x USB cable

VELLEMAN Basic Arduino Compatible Experimenter's Kit with ATMEGA328 Nano, VMA504

$39.90
What's Included: 1 ATmega328 NANO development board - VMA102 1 USB cable 1 Breadboard 30 Breadboard jumper wires 2 Light dependant resistors 1 IR remote receiver 4 Tactile switches 15 LEDs 1 Seven segment display 1 buzzer 1 50K potentiometer 2 Tilt switch 10 220 Ohm resistors 10 1k Ohm resistors

OSEPP 201 Arduino Basics Starter Kit, ARD-02

$99.00
Discover Arduino through EASY and FUN lessons Step-by-step instructions with diagrams No prior electronics knowledge required Kit comes with everything you need to build 15 projects across 8 categories: 1. Temperature 2. Light 3. LEDs 4. Sound 5. Ultrasonic 6. Servo Motors 7. Stepper Motors 8. LCD