Motors

Items 73 to 87 of 87 total

Grid List

HITEC HS-646WP High Voltage, High Torque, Analog Waterproof Servo, HS-646WP

$42.99
Hitec's waterproof servos have what it takes to keep your radio control vehicle, airplane or robot watertight! With high torque, dual ball bearings and metal gears, our analog waterproof servos have the industrys first IP67* rating ranking them among the most durable and reliable servos for wet conditions Whether you are manning your power boat, bashing in the mud, directing your underwater robot, or water landing your 25% plane, the HS-646WP will dependably keep your mind at ease

HITEC HS-311 Standard Economy Servo, HS-311

$8.99
The HS-311 sport servo provides the novice modeler all the performance and reliability you would expect to find in a more expensive servo Combined with precise resin gears and SMT circuitry

VELLEMAN TB6560 Stepper Motor Drive Board, VMA333

$16.40
6N137 high-speed OptoCouple to ensure high speed without losing steps for 42,57,86 Stepper within 3A  2/4 -phase / 4 wire / 6 wire stepper motor automatic half-decay excitation mode: synchronizing, half step, 1/8 step, 1/16 step current level is adjustable to meet your application needs large heat sink for good heat dissipation overheating and over-current protection circuit to ensure optimal performance operating voltage: 10 to 35 VDC rated output current: ± 3 A - peak 3.5 A dimensions: 50 x 75 x 35 mm weight: 80 g

VELLEMAN L293D Motor Drive Expansion Shield for Arduino, VMA207

$16.40
Two L293D Motor driver chips Four H-Bridges 0.6 A per bridge (1.2 A peak) Thermal shutdown protection Internal kickback protection diodes Up to 4 bi-directional DC motors Up to 2 stepper motors Pull down resistors to keep motors disabled during power-up Separate logic and motor power connections Terminal block connectors for motors and power motor voltages from 4.5 VDC to 16 VDC 2 connections for 5 V hobby servos

VELLEMAN DRV8825 Stepper Driver Board for K8400, VM8400DB

$18.55
simple step and direction control interface six different step resolutions: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step current adjust trimmer can interface directly with 3.3 V and 5 V systems over-temperature thermal shutdown, over-current shutdown and under-voltage lockout short-to-ground and shorted-load protection minimum operating voltage: 8.2 V maximum operating voltage: 45 V continuous current per phase: 1.5 A maximum current per phase: 2.2 A (with cooling) minimum logic voltage: 2.5 V maximum logic voltage: 5.25 V dimensions: 20 x 15 mm (0.8" x 0.6 ")

NTE 8-Channel Darlington Array/Driver ULN2803 Equivalent, 2018

$3.81
Ideally suited for interfacing between low−level digital logic circuitry and high−power peripheral loads High−voltage, high−current Darlington arrays in an 18−Lead DIP type package and feature peak load current ratings to 600mA for each of the eight drivers in each device Typical loads include relays, solenoids, stepping motors, multiplexed LED and incadescent displays, and heaters

OSEPP Motor Driver Module, MTD-01

$8.95
100% Arduino Compatible L298 dual h bridge driver Reverse motor polarity (motor direction)

VELLEMAN Dual H Bridge DC Stepper Motor Controller Board L298N, VMA409

$8.90
driver: L298N driver power supply: + 5 V to + 35 V driver output current (max.): 2A logic power output Vss: +5 V to +7 V (internal supply +5 V) logic current: 0-36 mA controlling level: low -0.3 V to 1.5 V, high: 2.3 V-Vss enable signal level: low -0.3 V to 1.5 V, high: 2.3 V-Vss max. current: 25 W working temperature: -13 °F to + 266°F (-25C to +130 °C) dimensions: 2.72" x 2.2" x 1.42" (69 x 56 x 36 mm)

OSEPP Motor & Servo Shield, SCSHD-01

$19.50
Mate with Arduino and Arduino compatible boards Provides connectors to support 2 servos. Servo power supply can be configured to source from the servo power terminal block or from the Arduinos 5V pin. Support up to 4 bi-directional DC motors with individual 8-bit speed selection, and up to 2 stepper motors (unipolar or bipolar) with single coil, double coil or interleaved stepping. Motor power supply can be configured to source from the motor power terminal block or from the Arduinos VIN pin. Support motors operating between 4.5V to 25V DC. Includes two L293D Quad H-Bridges chipset that can provide 0.6A per bridge (1.2A peak) with thermal shutdown protection, internal kickback protection diodes. Provides DIP sockets to support other pin compatible motor bridge chipset. Integrated pull down resistor to keep motor disable during start up. Individual LED indicator for motor power supply state and servo power supply state. Brings out the Arduinos reset button to the top of the shield

VELLEMAN 5VDC Stepper Motor with ULN2003 Driver Board, VMA401

$4.85
LED step indicators included: 5 V stepper motor ULN2003 controller module Cable Specifications: Operating Voltage: 5 VDC Steps / revolution: 64 Controller: ULN2003 motor diameter: 28 mm Reduction ratio: 1:64 number of phases: 4 dimensions: 35 x 32 x 10 mm

POLOLU Stepper Motor: Bipolar, 200 Steps/Rev, 2030mm, 3.9V, 0.6 A/Phase, 1204

$17.95
Size: 20 mm square × 30 mm, not including the shaft (NEMA 8) Weight: 60 g (2 oz) Shaft diameter: 4 mm “D” Steps per revolution: 200 Current rating: 600 mA per coil Voltage rating: 3.9 V Resistance: 6.5 Ω per coil Holding torque: 180 g-cm (2.5 oz-in) Inductance: 1.7 mH per coil Lead length: 30 cm (12″) Output shaft supported by two ball bearings NEMA 8

Stepper Motor: Bipolar, 200 Steps/Rev, 2832mm, 3.8V, 0.67 A/Phase, 1205 POLO

$15.95
Size: 28 mm square × 32 mm, not including the shaft (NEMA 11) Weight: 110 g (4 oz) Shaft diameter: 5 mm “D” Steps per revolution: 200 Current rating: 670 mA per coil Voltage rating: 3.8 V Resistance: 5.6 Ω per coil Holding torque: 600 g-cm (8.3 oz-in) Inductance: 4.2 mH per coil Lead length: 30 cm (12″) Output shaft supported by two ball bearings

Stepper Motor: Unipolar/Bipolar, 200 Steps/Rev, 4248mm, 4V, 1.2 A/Phase, 1200

$19.95
Size: 42.3 mm square × 48 mm, not including the shaft (NEMA 17) Weight: 350 g (13 oz) Shaft diameter: 5 mm “D” Steps per revolution: 200 Current rating: 1.2 A per coil Voltage rating: 4 V Resistance: 3.3 Ω per coil Holding torque: 3.2 kg-cm (44 oz-in) Inductance: 2.8 mH per coil Lead length: 30 cm (12″) Output shaft supported by two ball bearings NEMA 17 size

OSEPP Stepper Motor & Driver, STEPD-01

$14.95
100% Arduino Compatible ULN2003A driver chip controls unipolar & bipolar stepper motors