Motors

27 Item(s)

Grid List

SPARKFUN Liquid Pump - 350GPH (12v), ROB-10455

$16.90
12V operation 350 GPH 1.5A motor " barbed outlet 3ft long wire leads

SPARKFUN Hobby Motor with Gear 1-3 VDC, ROB-11696

$2.10
1.0 to 3.0VDC Motor but can handle a max load of up to 12VDC No load speed of 660010% RPM (@1.0V DC, 110mA).

OSEPP 18 RPM Economy Gear Motor, LS-00087

$15.35
6-18VDC operating voltage 19RPM 0.12A no load current 3.9A stall current 2,678.28 oz-in (192.86 kgf-cm) torque stall 4mm shaft

SPARKFUN Vacuum Pump 12VDC, ROB-10398

$20.85
12V motor 12W operation " barbs 0-16" Hg vacuum range

OSEPP R260 3-6V 12000 RPM Brushed DC Motor, LS-00026

$3.28
Small R260 Brushed DC Motor Nominal Voltage: 3V No Load RPM: 7000rpm (±10%) Shaft Diameter: 2mm

OSEPP F130 1.5-3V 12000 RPM Brushed DC Motor, LS-00024

$3.28
1 x F130 1.5-3V 12000 RPM Brushed DC Motor Small Flat Side F130 Brushed DC Motor Nominal Voltage: 3V No Load RPM: 13800rpm (±10%) Shaft Diameter: 2mm

OSEPP R140 1.5-3V 10000 RPM Brushed DC Motor, LS-00025

$3.28
1 x R140 1.5-3V 10000 RPM Brushed DC Motor Small Round R140 Brushed DC Motor Nominal Voltage: 3V No Load RPM: 13000rpm (±10%) Shaft Diameter: 2mm

TAMIYA 4-Speed Worm Gearbox Kit, 72008

$19.50
This versatile, high-efficiency gearbox lets you build one of the following gear ratios: 11.6:1, 29.8:1, 76.5:1, 196.7:1, 505.9:1, and 1300.9:1.

OSEPP Fan Motor Module, FAN-01

$8.95
Operating voltage output: 3V 6V MAX Speed (no load):15000 rpm Speed (6V):8000 rpm Current (6V):40mA Stall current (6V):360mA Torque (6V):0.111kg/cm

HITEC HSR-1425CR Servo Continuous Rotation, HSR-1425CR

$16.99
The HSR-1425CR is the continuous rotation version of the HS-425HB The speed is proportional meaning that the further the PWM signal deviates from the idle signal (approximately 1500usec) the faster the servo will rotate If you're looking for the smoothest continuous rotation servo, be sure to check out the HSR-2645CR servo

OSEPP Motor Encoder (set of 2), ENC-01

$19.95
4.5 – 24 Volt operation 11 pole encoder Two solid state 3144 Hall effect sensors 100% Arduino compatible Designed for 25mm DC motors Package Content 2 x Motor Encoders 2 x Metal mounts (for 25mm motors) 2 x Magnets

HITEC HSR-2645CR Servo Continuous Rotation, HSR-2645CR

$31.99
While regular servos that get modified to continuous rotation tend to be difficult to control the speed on, the HSR-2645CR circuit was designed from the factory to drive the servo smoothly and with fine-control over the speed Since the HSR-2645CR servo is digital, it's able to be tuned using a Hitec servo programmer The programmable parameters allow you to tailor the servo to best-fit your application Excellent for compact sliders, winch mechanisms, small panning devices and wheel-drives on robots

OSEPP Standard Economy Servo Motor, LS-5010SR

$9.89
Voltage Range:  4.8 – 7.2 Volts Stall Torque (6.0V): 4.1 kg.cm Stall Torque (4.8V): 3.2kg.cm JR Wire Configuration No-load Speed (6.0V / 4.8V):  0.19sec/60° / 0.23sec/60° Dimensions: 40.8*20.1*38mm Weight: 44g Rotation: 180 degrees Output Shaft Style: 25 tooth spline

OSEPP Standard Economy Servo Motor Contiuous Rotation, LS-5010CR

$19.95
Suitable for hobby, models, science and other projects. Comparable to Servocity # 31311S20 Voltage Range:  4.8 – 7.2 Volts Stall Torque (6.0V): 4.1 kg.cm Stall Torque (4.8V): 3.2kg.cm JR Wire Configuration No-load Speed (6.0V / 4.8V):  0.19sec/60° / 0.23sec/60° Dimensions: 40.8*20.1*38mm Weight: 44g Rotation: Continuous Output Shaft Style: 25 tooth spline

NTE 8-Channel Darlington Array/Driver ULN2803 Equivalent, 2018

$3.81
Ideally suited for interfacing between low−level digital logic circuitry and high−power peripheral loads High−voltage, high−current Darlington arrays in an 18−Lead DIP type package and feature peak load current ratings to 600mA for each of the eight drivers in each device Typical loads include relays, solenoids, stepping motors, multiplexed LED and incadescent displays, and heaters

OSEPP Motor Driver Module, MTD-01

$17.59
100% Arduino Compatible L298 dual h bridge driver Reverse motor polarity (motor direction)

OSEPP Motor & Servo Shield, SCSHD-01G

$18.95
Mate with Arduino and Arduino compatible boards Provides connectors to support 2 servos. Servo power supply can be configured to source from the servo power terminal block or from the Arduinos 5V pin. Support up to 4 bi-directional DC motors with individual 8-bit speed selection, and up to 2 stepper motors (unipolar or bipolar) with single coil, double coil or interleaved stepping. Motor power supply can be configured to source from the motor power terminal block or from the Arduinos VIN pin. Support motors operating between 4.5V to 25V DC. Includes two L293D Quad H-Bridges chipset that can provide 0.6A per bridge (1.2A peak) with thermal shutdown protection, internal kickback protection diodes. Provides DIP sockets to support other pin compatible motor bridge chipset. Integrated pull down resistor to keep motor disable during start up. Individual LED indicator for motor power supply state and servo power supply state. Brings out the Arduinos reset button to the top of the shield

Stepper Motor: Bipolar, 200 Steps/Rev, 2832mm, 3.8V, 0.67 A/Phase, 1205 POLO

$20.95
Size: 28 mm square × 32 mm, not including the shaft (NEMA 11) Weight: 110 g (4 oz) Shaft diameter: 5 mm “D” Steps per revolution: 200 Current rating: 670 mA per coil Voltage rating: 3.8 V Resistance: 5.6 Ω per coil Holding torque: 600 g-cm (8.3 oz-in) Inductance: 4.2 mH per coil Lead length: 30 cm (12″) Output shaft supported by two ball bearings